Empire State High- and Low-Speed Rail

If Swiss planners were hired to design an intercity rail network for New York State, they might propose something that looks like this:

The trip times depicted on the map are a few minutes longer than intended, especially next to a terminus station like Niagara Falls, Watertown, and Ithaca. The depicted times are inclusive of turnaround time: the 45-minute Buffalo-Niagara Falls line is intended to take around 35 minutes in actual service, with 10-minute turnarounds.

Swiss planning is based on hourly and half-hourly timetables repeating all day on a clockface pattern: if a train leaves your station at 8:24 am, a train will leave your station at xx:24 all day, and if the line runs every half hour then also at xx:54. Moreover, at major nodes, trains are timetabled to arrive a few minutes before the hour and depart a few minutes after, letting passengers connect between different trains with minimal wait. To minimize transfer time and turn time, trains run as fast as necessary – that is, the state invests in higher-speed lines to ensure connections between major cities take a few minutes less than an hour. The Bahn 2000 program set up connections between Zurich, Basel, and Bern taking just less than an hour, with a few further connections elsewhere taking just less than an integer number of half-hours; the Bahn 2030 program aims to do the same with more cities all over the country.

The above map is an adaptation of the concept to New York State. I hope the explanation of how to adapt Switzerland to New York will be of interest to rail advocates elsewhere – the differences between the two geographies matter elsewhere, for example in Germany, France, or Sweden, or for that matter in California or New England.

High-speed rail

There is no high-speed rail in Switzerland, unless one counts the mixed passenger and freight rail tunnels through the Alps, which allow 250 km/h passenger trains. The Bahn 2030 planning calls for a 2-hour trip time between Zurich and Lugano, a distance of about 170 km, even with heavy tunneling under all significant mountains; with so much tunneling, 1.5-hour trips are easy and even 1-hour trips are feasible with a bypass around Zug. Clearly, even when higher speeds are allowed, Swiss planning sticks to low- and medium-speed rail, targeting an average speed of about 120 km/h.

This works for Switzerland, a small country in which even Geneva is only 2:45 from Zurich. In New York, it does not. At the speed of upgraded legacy rail, comparable to the Northeast Corridor, the links on the above map along the high-speed spine would take 2 hours each rather than an hour. New York-Buffalo trains would take 6 hours, too long for most travelers, and New York-Rochester would take 5 hours, which is marginal at best. Trains doing New York-Albany in 2 hours could get fairly popular, but even that is long enough that cutting it to just less than an hour is feasible.

Frequency

Trains are to run every half hour, with the exception of urban lines, namely Buffalo-Niagara Falls, Albany-Troy-Mechanicsville, and Utica-Rome, which run every 15 minutes. The reason for the half-hourly frequency is that all lines need it for either capacity or ridership. The lines either run to New York, which is so big it can easily fill a train every half hour and perhaps even every 15 minutes, or are quite short, so that running only every hour reduces ridership and it’s better to run shorter trains every 30 minutes.

With half-hourly timetables, a stub-end line can take an integer number of quarter-hours and not just half-hours. For example, Syracuse and Albany should have a pulse at :00 and :30 every hour. This in turn means that trains from Albany to Glens Falls can take 1:15, departing Albany just after :00 and :30, arriving at Glens Falls just before :15 and :45, turning back toward Albany just after :15 and :45, and then returning to Albany just before :00 and :30.

The only worry with quarter-hour trip times is that every cycle must sum up to an integer number of half-hours, not quarter-hours. Otherwise, some connections are broken, offset by 15 minutes. Thankfully, the only cycle on this map is New York-Albany-Syracuse-Binghamton-New York, which takes 7 hours.

Syracuse regional rail

Syracuse is depicted as having the most expansive regional rail network in the state, despite being the smallest of Upstate New York’s four major metropolitan areas. The reason is that the goal of the planned network is to provide intercity rather than local service. Rochester has some useful urban lines, for example to Freeport or northwest to the lakefront, but they are so short that they should run every 10 or 15 minutes and not every half hour. However, Rochester has no significant independent towns within an hour or so by rail, and thus there are no timed connections there. In contrast, Syracuse is located right between Watertown, Oswego, Auburn, and Cortland with its connection onward to Ithaca.

The Syracuse system is intended to be fully on the RegionalBahn side of the S-Bahn vs. RegionalBahn divide. The shared segment between Syracuse and the split between the lines to Oswego and Watertown is not meant to overlay to run frequent urban service. Instead, trains should tailgate, followed by a gap of nearly half an hour. Syracuse-bound trains may well call at Liverpool at :20 and :22, arriving at Syracuse at :25 and :27 to exchange passengers with other trains and then continue south, one of Oswego and Watertown paired with Cortland and Binghamton and the other terminating. If north-south S-Bahn service is desired, trains should be slotted in between the intercity trains.

New lines

The map depicts greenfield alignments for the high-speed line except on the approaches to New York and Toronto, and legacy alignments for the low-speed lines.

As in Switzerland, the low-speed lines do not necessarily slavishly adhere to legacy alignments. However, the deviations are not the same. Switzerland uses bypasses and tunnels to speed lines up. In New York, the main mechanisms to speed up lines are electrification, track renewal, and higher superelevation. Tunnels are too expensive for the population density of Upstate New York. I can see some bypasses, potentially getting Syracuse-Cortland and Cortland-Binghamton down to 30 minutes each, but none of the Upstate cities off the high-speed line is big enough to justify major civil works.

The one depicted bypass on a blue-colored line is the use of the Boonton Branch in New Jersey to offer an express bypass around the Morristown Line with its dense station spacing. This requires some additional tracks on busy urban regional lines as well as a short tunnel in Paterson, but New York is big enough that investing in faster service to Dover, Delaware Water Gap, and Scranton is worth it.

Upstate, the important deviations involve restoring old tracks, including between Cortland and Ithaca and within some town centers. Corning and Glens Falls both have disused rail alignments serving their centers better than the existing freight lines. But most importantly, Syracuse has an underused freeway running east-west through its center, which I am assuming replaced with a rail line. This is not a new idea – Syracuse is already removing a branch of the freeway, which should be used for a rail connection toward Binghamton, and even the mainline is a vestige of when midcentury planners thought Upstate cities would keep growing. The current Syracuse station is at an inconvenient location, making rail realignment a good use of the right-of-way.

Onward connections

New York State is much more integrated with its neighbors than Switzerland – it’s all the same country. There is extensive interstate travel, and rail planning must accommodate this. Forget the Deutschlandtakt – an Americatakt would be the most complex rail plan in a developed country out of sheer size. Thankfully, the connections depicted on the New York State plan accommodate interstate travel fairly well.

Going east, there are connections to Vermont, Massachusetts, and Connecticut. Albany-Boston can be done in around an hour, which makes for a half-hour takt connection between Albany and Springfield and 45 minutes minus turnaround between Springfield and Boston. Springfield-New Haven is 30 minutes by high-speed rail or 45 minutes by fast legacy rail, both with a stop at Hartford and few to no others; Springfield can then get its own small regional rail line toward Northampton (with some urban overlays for an S-Bahn) and Greenfield. Vermont can get a slow line to Rutland, and/or a fast line to Burlington continuing to Montreal; thence New York-Montreal and Boston-Toronto trains can be timed to connect at Albany, with New York-Toronto trains slotted in between, timed to connect only to the more frequent urban lines like Buffalo-Niagara Falls.

Going south, New York is separated from Pennsylvania by the northern reach of the Appalachians, called the Southern Tier in New York and the Northern Tier in Pennsylvania. This area had many coal mines in the 19th century and as a result has many legacy rail lines, but they are curvy and connect villages. But Scranton is a significant city on a nice line with Allentown and Philadelphia; unfortunately, the Philadelphia-Allentown line stretches via Reading and the Allentown-Scranton line is hilly and curvy, justifying some greenfield construction with some tunneling near the northern end.

Finally, going west, the I-90 route serves Erie and the Midwest. But this is a plausible high-speed rail connection toward Chicago, and so no low-speed interface is needed within the state. Erie could get a line to Youngstown and Pittsburgh, but it would be slower than connecting between high-speed trains in Cleveland; the largest city between Erie and Youngstown is Meadsville, population 13,000.

Costs

The cost of the high-speed spine is considerable, but if New York can keep it to the level of France (around $25 million/km), or even Germany (around $35 million/km), the benefits should exceed the costs. New York is huge, and even though nothing in Upstate New York is, the combined populations of Syracuse, Rochester, and Buffalo would add up to a big French or German city. And then there is Toronto at the other end, anchoring everything.

The low-speed lines should be quite cheap. Track renewal in Germany is around $1 million per single-track kilometer; at the frequency envisioned, all the low-speed lines can stay single-track with passing segments. Electrification is maybe $1.5 million per kilometer in Israel, despite a lawsuit that delayed the project by three years.

Is this feasible?

Technically, all of this is feasible. Good transit advocates in the Northeastern United States should push elected officials at the federal and state levels to quickly plan such a system and aim to begin construction early this decade. Bahn 2000 was supposed to take the 1990s to be built, but was delayed to 2004; this is a bigger program but can still happen by 2030 or so.

The trip times, frequencies, and coverage chosen for the map are deliberately conservative. It’s possible to squeeze higher speed at places, and add more branches to smaller towns, like Rochester-Niagara Falls or Buffalo-Jamestown. Bahn 2000 is followed up with Bahn 2030 or Bahn 2035, and likewise rail improvements can accrete in the United States. But as a starter system, this is a solid network connecting all large and nearly all small cities in New York State to one another with maximum convenience and minimum hassle. I hope state planners take heed and plan to invest soon.

International Links: a Revision

In 2011, I wrote a post arguing that international links underperform. I gave examples, using many links nearly all of which have rotted in the 8.5 years since, showing that the ridership on various air and rail city pairs was lower if they were in two different countries than if they were in the same country. The most important example is Eurostar, connecting London and Paris. Eurostar has 11 million passengers per year, of which a growing minority go between London and cities other than Paris, like Brussels and Amsterdam. In contrast, the TGVs from Paris to the southeast have 44.4 million annual passengers; the major secondary cities on the line combine to about half of London’s population. The newly-opened LGV Sud-Europe-Atlantique has 6 million annual passengers on the Paris-Bordeaux city pair alone – and Bordeaux has an order of magnitude fewer inhabitants than London.

My assumption was always that Eurostar’s problem is that it connects two distinct countries, speaking two different languages. Thus, similar international connections, like oft-mooted proposals for high-speed rail between New York or Boston and Montreal or even between New York and Toronto, are likely to severely underperform domestic ones. This is not too relevant to the United States, which is not building high-speed rail of any kind, but is increasingly relevant to Europe, which is slowly building international links. But what if the assumption that the important aspect is the national or linguistic border is incorrect? What if there are other issues on Eurostar and various international air links, which national railroads can choose to solve if they care?

The issue of fares

I fired up Eurostar and SNCF’s sites and looked for tickets departing Tuesday in 13 days. I got 14 trains from London to Paris, charging fares ranging from €52.50 to €144.50. The average is €91.46, and the median is €98.50. From Paris to Lyon, I got 22 regular TGVs (“InOui”), charging €45-97, with an average of €84.63 and a median of €97 – but I also got 5 OuiGo trains, charging €10-25, all but one leaving from Gare de Lyon rather than Marne-la-Vallée with its difficult RER transfer.

On city pairs where SNCF expects more competition than Paris-Lyon, fares are lower, even when trips are longer. Paris-Marseille has 15 regular InOui departures and 8 OuiGos; the InOuis charge €49-79 with an average of €57.33, and the OuiGos charge €10-28, half serving Paris proper and half leaving from Marne-la-Vallée. The OuiGo services overall are unprofitable, but the InOuis aren’t – the Spinetta Report claims the fully-laden cost of TGV service is €0.07/seat-km, and seat utilization is very high (too high, in fact – it’s at the expense of off-peak frequency).

The other international service using the LGV Nord, Thalys, charges high fares as well, if less high than Eurostar. The site shows me 18 departures from Paris to Brussels on the 4th of February; one has a €29 ticket, but the others state that cheap ticket is sold out and offer me €66-99 tickets and one is entirely sold out. Going to Amsterdam, there are 10 departures, charging €98-135. To Cologne, the final of the major cities served by Thalys, there are 5 departures, one with a cheap €35 ticket and the rest charging €76-122. Thalys has 7.5 million annual riders, roughly within the same range relative to metro area population one would expect from Eurostar, depending on what one counts as the metro areas of Rotterdam, Amsterdam, and Cologne.

I compare Eurostar and Thalys with domestic TGVs not just out of convenience. SNCF owns a majority stake in Eurostar and Thalys. The yield management systems are likely similar, making a comparison of trips on the same day reasonable. In contrast, I would not want to do such a comparison with, say, the Shinkansen, which has no yield management at all and charges the same fare for the same class of seat and train speed.

The consequence of high fares

It’s quite likely, then, that the low ridership on Eurostar is connected with its high fares. Once tickets are expensive enough to discourage price-conscious customers, the ridership profile consists of price-insensitive travelers, making it possible to keep escalating fares.

A 2009 study by Christiaan Behrens and Eric Pels on air-rail competition in the London-Paris market finds that in a nested logit model, Eurostar travelers have a price elasticity of -0.14 to -0.15, compared with about -0.43 out of Heathrow on BA for businesses travelers and -0.77 for leisure travelers. The study compares different airlines and airport choices, with most of the market in the 2000s using Heathrow and either BA or Air France, with Air France having higher elasticity. In a mixed logit model, fare elasticities are all much higher, but Eurostar is still much more inelastic than flying, around -0.50 vs. -1 for business flyers and -2.5 for leisure flyers.

The second link in this post mentions growth in American tourist travel as a reason for Eurostar’s recent growth in ridership. It is not surprising that foreign tourists who paid high fares to travel to Europe and are staying in expensive hotels are a significant source of revenue to Eurostar. Presumably American tourist travel on domestic TGVs is up too, but it is far less significant, first because no secondary French city has the tourism of Paris and London except for Nice, 5.5 hours from Paris by train, and second because the domestic market is strong enough that American tourists are barely a blip on the radar.

Regardless, the elevated American tourist numbers present a peril to the state of the American discourse on the subject, even if they generate much-needed revenue for SNCF. Those tourists then come back to the US talking up the convenience of high-speed rail, or at least the version of it with security theater and passport checks, but bemoan the high ticket prices.

We already see what happens when train trips are priced for the top of the market in the United States. Fares per the 2016 annual report, the most recent one to include this data (on PDF-p. 41), average $0.58/p-km on the Acela and $0.30/p-km on the Regional; per an ARAFER report using 2016 data, the corresponding number for domestic TGVs is €0.10/p-km (PDF-pp. 15, 26). With Amtrak’s cheaper trains charging 2.5 times as much as the TGVs, price-conscious travelers decamp for intercity buses – just as price-conscious Europeans ride FlixBus where train travel options are too slow or too expensive. By now, a decade after Megabus and Bolt entered the market, Amtrak is largely only used by people who are price-insensitive or who get motion-sick on buses.

Why are they like this?

If the problem is that international links underperform because they are expensive, then it raises the question, why are fares high to begin with? SNCF charges high fares on Thalys and Eurostar, but not on its domestic trains. This isn’t just about American tourists – I heard too few American accents when I took Eurostar for Americans to be a big enough proportion of revenue. Nor is this about business travelers, because there are many of these traveling between Paris and other French cities.

Rather, my suspicion is that the difference is political. National railroads offering domestic train service face demands from various interests in different directions: the executives themselves as well as the treasury want to maximize revenue, the government writ large wants to give the appearance of successful service, the public wants cheap travel. The major European national railroads seem to have converged on the same solution: intercity trains are not to receive public subsidy for operations or depreciation, but subject to that constraint they should set fares to maximize ridership rather than revenue. The EU even promotes this policy – its directives on passenger rail competition do not allow state subsidies on routes with competition, but do not mandate revenue-maximizing fares.

The political pressure on international rail services is different. The riders are usually foreigners. There is no populist pressure to keep fares low, even on the many French citizens who ride trains to London and Brussels – on the contrary, any inkling of the state not extracting maximum revenue from foreigners may lead to populist pressure to increase fares.

It is possible that more competition will lower fares. This happened in the domestic Italian market, where the entrance of NTV’s Italo service reduced fares on the thicker markets. There is some competition between Paris and points east, such as Frankfurt, where SNCF runs a daily TGV, charging €45 on the 4th of February and DB runs 4 daily ICEs, charging €70-90. Averaged out, it is barely higher than the domestic TGV fare per kilometer.

Which international connections become viable?

European high-speed rail networks are largely domestic. Eurostar stands as the one major exception. What’s more, France, Italy, and Spain have already built the strongest domestic corridors; the only low-hanging domestic fruit are in Germany, where high-speed construction is desirable but is beset by economic austerity, and Britain, where it is beset by very high construction costs. The future of European rail investment is therefore international.

I do not want to claim that charging domestic TGV or ICE fares will automatically lead to ridership density comparable to that of domestic TGVs and ICEs. The language difference probably still matters, just not to the point that Eurostar’s ridership is one quarter that of the LGV Sud-Est.

Moreover, some international routes are clearly a low political priority, so the infrastructure is not optimized for them, leading to low speeds. Trains leaving Brussels going north and east run on a mixture of fast and slow lines, and overall average speeds from Brussels to both Cologne and Amsterdam are within the range for all-legacy upgraded lines. French rail planners, infused by ideas of airline executives who think trains aren’t competitive past three hours, are not trying to optimize the under-construction Mont d’Ambin Base Tunnel for intercity passenger traffic, on the theory that Paris-Turin and Paris-Milan trains would not be competitive either way.

So it’s important to get everything on an international connection right: breakeven rather than revenue-maximizing fares, infrastructure optimized for speed between different cities, sufficient frequency relative to travel time. If these are done right, then city pairs that may look weak may become attractive high-speed rail corridors: Paris-Frankfurt, Paris-Madrid via Bordeaux and Basque Country, Munich-Milan via Innsbruck and the Brenner Base Tunnel, Madrid-Lisbon, Hamburg-Copenhagen, Cologne-Amsterdam.

This is applicable in North America as well, except that there, an additional complication is border controls; the hassle must be reduced to preclearance with short lines (maximum 10-15 minutes), or ideally eliminated with a Schengen-style agreement. This affects Vancouver-Seattle and Toronto-New York, both of which look marginal if we assume international links always underperform. If we accept that New York and Toronto share a language and many cultural features and the weak air travel market is an artifact of high fares, then cross-border trains become an attractive target for investment. In that scenario, New York-Toronto is the strongest North American high-speed rail corridor not touching the Northeast Corridor – it’s like Los Angeles-San Francisco but with stronger connecting public transportation and no mountains to tunnel under.

The upshot is that, given good management, there remains a future for high-speed rail investment, with a plethora of strong lines. The EU can and should take an active role in promoting Union-wide links, ensuring that fares are within the reach of the broad public and that connections between any pair of European cities are reasonable. In North America, two specific links are strong – New York-Toronto and Seattle-Vancouver – and so the federal governments as well as the states and provinces should make sure to invest in them and to charge affordable fares with minimally intrusive border control.

Transfers from Infrequent to Frequent Vehicles

Imagine yourself taking a train somewhere, and imagine the train is big and infrequent. Let’s say it’s the commuter train from New York down the Northeast Corridor to Newark Airport, or perhaps a low-cost OuiGo TGV from Lyon to Paris. Now imagine that you change trains to a small, frequent train, like the AirTrain to Newark Airport, or the RER from the OuiGo stop in the suburbs to Paris itself. What do you think happens?

If your guess is “the train I’m connecting to will be overcrowded,” you are correct. Only a minority of a 200 meter long New Jersey Transit train’s ridership unloads at the Newark Airport station, but this minority is substantial enough to overwhelm the connection to the short AirTrain to the terminals. Normally, the AirTrain operates well below capacity. It uses driverless technology to run small vehicles every 3 minutes, which is more than enough for how many people connect between terminals or go to New York by train. But when a big train that runs every 20-30 minutes arrives, a quantity of passengers who would be easily accommodated if they arrived over 20 minutes all make their way to the monorail at once.

In Paris, the situation is similar, but the details differ. Until recently, OuiGo did not serve Paris at the usual terminal of Gare de Lyon but rather at an outlying station near Eurodisney, Marne-la-Vallée-Chessy, ostensibly to save money by avoiding the Gare de Lyon throat, in reality to immiserate passengers who don’t pay full TGV fare. There, passengers would connect from a 400-meter bilevel TGV on which the entire train ridership would get off to a 220-meter bilevel RER train running every 10 minutes. The worst congestion wasn’t even on the RER itself, but at the ticket machines: enough of the thousand passengers did not have Navigo monthly cards for the RER that long lines formed at the ticket machines, adding 20 minutes to the trip. With the RER connection and the line, the trips would be nearly 3.5 hours, 2 spent on the high-speed train and 1.5 at the Paris end.

I even saw something similar in Shanghai in 2009. I visited Jiaxing, an hour away at the time by train, and when I came back, a mass of people without the Shanghai Public Transportation Card overwhelmed the one working Shanghai Metro ticketing machine. There were three machines at the entrance, but two were out of service. With the 20 minutes of standing in line, I would have gotten back to my hotel faster if I’d walked.

This is a serious problem – the ticketing machine lines alone can add 20 minutes to an otherwise 2.5-hour door-to-door trip. To avoid this problem, railroads and transit agencies need a kit with a number of distinct tools, appropriate for different circumstances.

Run trains more frequently

Commuter trains have to run frequently enough to be useful for short-distance trips. If the RER A consistently fills a train every 10 minutes off-peak between Paris and Marne-la-Vallée, New Jersey Transit can consistently fill a local train every 10 minutes off-peak between Manhattan and New Brunswick. Extra frequency induces extra ridership, but fewer people are going to get off at the Newark Airport stop per train if trains run more often. There are some places where adding frequency induces extra ridership proportionately to the extra service, or even more, but they tend to be shorter-range traffic, for example between Newark and Elizabeth or between Newark and New York.

This tool is useful for urban, suburban, and regional service. A train over a 20 kilometer distance can run frequently enough that transfers to more frequent shuttles are not a problem. Even today, this is mostly a problem with airport connectors, because it’s otherwise uncommon for outlying services to run very frequently. The one non-airport example I am familiar with is in Boston on the Mattapan High-Speed Line, a light rail line that runs every 5 minutes, connecting Mattapan with Ashmont, the terminus of the Red Line subway, on a branch that runs every 8-9 minutes at rush hour and every 12-15 off-peak.

In contrast, this tool is less useful for intercity trains. France should be running TGVs more frequently off-peak, but this means every half hour, not every 10 minutes. The only long-distance European corridors that have any business running an intercity train every 10 minutes are Berlin-Hanover(-Dortmund) and Frankfurt-Cologne, and in both cases it comes from interlining many different branches connecting huge metropolitan areas onto a single trunk.

Eliminate unnecessary transfers

The problem only occurs if there is a transfer to begin with. In some cases, it is feasible to eliminate the transfer and offer a direct trip. SNCF has gradually shifted OuiGo traffic from suburban stations like Marne-la-Vallée and Massy to the regular urban terminals; nowadays, five daily OuiGo trains go from Lyon to Gare de Lyon and only two go to Marne-la-Vallée.

Gare de Lyon is few people’s final destination, but at a major urban station with multiple Métro and RER connections, the infrastructure can handle large crowds better. In that case, the transfer isn’t really from an infrequent vehicle, because a TGV, TER, or Transilien train unloads at Gare de Lyon every few minutes at rush hour. The Métro is still more frequent, but at the resolution of a mainline train every 5 minutes versus a Métro Line 1 or 14 train every 1.5 minutes, this is a non-issue: for one, passengers can easily take 5 minutes just to walk from the far end of the train to the concourse, so effectively they arrive at the Métro at a uniform rate rather than in a short burst.

Of note, Shanghai did this before the high-speed trains opened: the trains served Shanghai Railway Station. The capacity problems occurred mostly because two out of three ticketing machines were broken, a problem that plagued the Shanghai Metro in 2009. Perhaps things are better now, a decade of fast economic growth later; they certainly are better in all first-world cities I’ve taken trains in.

Eliminating unnecessary transfers is also relevant to two urban cases mentioned above: airport people movers, and the Mattapan High-Speed Line. Airport connectors are better when people do not need to take a landside people mover but rather can walk directly from the train station to the terminal. Direct service is more convenient in general, but this is especially true of airport connectors. Tourists are less familiar with the city and may be less willing to transfer; all passengers, tourists and locals, are likely to be traveling with luggage. The upshot is that if an airport connector can be done as an extension of a subway, light rail, or regional rail line, it should; positive examples include the Piccadilly line and soon to be Crossrail in London, the RER B in Paris, and the S-Bahn in Zurich.

The Mattapan High-Speed Line’s peculiar situation as an isolated tramway has likewise led to calls for eliminating the forced transfer. Forces at the MBTA that don’t like providing train service have proposed downgrading it to a bus; forces within the region that do have instead proposed making the necessary investments to turn it into an extension of the Red Line.

Simplify transfer interfaces

The capacity problem at the transfer from an infrequent service to a frequent one is not just inside the frequent but small vehicle, but also at the transfer interface. Permitting a gentler interface can go a long way toward solving the problem.

First, tear down the faregates. There should not be fare barriers between different public transport services, especially not ones where congestion at the transfer point can be expected. Even when everything else is done right, people can overwhelm the gates, as at the Newark Airport train station. The lines aren’t long, but they are stressful. Every mistake (say, if my ticket is invalid, or if someone else tries to ask the stressed station agent a question) slows down a large crowd of people.

And second, sell combined tickets. Intercity train tickets in Germany offer the option of bundling a single-ride city ticket at the destination for the usual price; for the benefit of visitors, this should be expanded to include a bundled multi-ride ticket or short-term pass. New Jersey Transit sells through-tickets to the airport that include the AirTrain transfer, and so there is no congestion at the ticketing machines, only at the faregates and on the train itself.

Both of these options require better integration between different service providers. That said, such integration is clearly possible – New Jersey Transit and Port Authority manage it despite having poor fare and schedule integration elsewhere. In France in particular, there exist sociétés de transport functioning like German Verkehrsverbünde in coordinating regional fares; SNCF and RATP have a long history of managing somehow to work together in and around Paris, so combined TGV + RER tickets, ideally with some kind of mechanism to avoid forcing visitors to deal with the cumbersome process of getting a Navigo pass, should not be a problem.

Cops on Public Transportation

I wrote a post about American moral panics about fare evasion two months ago, which was mirrored on Streetsblog. I made a mistake in that post that I’d like to correct – and yet the correction itself showcases something interesting about why there are armed police on trains. In talking about BART’s unique belts-and-suspenders system combining faregates with proof-of-payment fare inspections, I complained that BART uses armed police to conduct inspections, where the German-speaking world happily uses unarmed civilians. BART wrote me back to correct me – the inspections are done by unarmed civilians, called ambassadors. The armed cops on the trains are unrelated.

I’d have talked about my error earlier, but I got the correction at the end of November. The American Christmas season begins around Thanksgiving and ends after Sylvester, and in this period both labor productivity and news readership plummet; leave it to Americans to have five weeks a year of low productivity without giving workers those five weeks in vacation time. With that error out of the way – again, BART conducts inspections with unarmed ambassadors, not armed cops – it’s worth talking about why, then, there are armed cops on trains at all, and what it means for fare enforcement.

The answer to the “why armed cops on the train?” question is that among the broad American public, the police is popular. There are hefty differences by party identification, and in the Bay Area, the opinions of Republicans are mostly irrelevant, but even among Democrats; there are also hefty differences by race, but blacks are at their most anti-police divided on the issue. A Pew poll about trust in institutions asks a variety of questions about the police, none of which is “would you like to see more cops patrol the subway?”, but the crosstabs really don’t scream “no.” Vox cites a poll by Civis Analytics that directly asks about hiring more police officers, and even among black people the results are 60-18 in favor. In New York, NYPD Commissioner James O’Neill had positive net approval among all racial groups shortly before leaving office, the lowest rate being 43-28 among Hispanics.

The crosstabs only go so far, and it’s likely that among certain subgroups the police is much less popular, for example black millennials. It’s normal for a popular institution to still generate intense opposition from specific demographic, class-based, or ideological groups, and it’s even normal for a popular institution to be bad; I should know, Massachusetts’ Charlie Baker is one of America’s most popular governors and yet his do-nothing approach to infrastructure planning makes him unpopular at TransitMatters. But this doesn’t change the fact that, as a positive rather than normative statement, the police enjoys consensus support from the urban American public.

What this means is that there are cops on the subway in New York and on BART not because of an inherent necessity of the fare collection system, but because in the eyes of the people who run these systems, crime is a serious concern and having more cops around is the solution. Evidently, BART layers cops on top of two distinct fare enforcement mechanisms – fare barriers and the ambassadors. In New York, too, NYPD’s justification for arresting people for jumping the turnstiles is that a significant fraction of them have outstanding warrants (many of which are about low-level offenses like being behind on court payments).

I bring this up because there’s a growing argument on the American left that public transportation should be free because that way people won’t be arrested for fare-dodging. This argument slides in an assumption, all too common to socialists who are to the left of the mainline liberal or social democratic party, that there is a leftist majority among the public that is just waiting to be activated by a charismatic leader rejecting neoliberal or otherwise moderate political assumptions.

But in the real world, there is no such leftist majority. The median voter even in a very left-wing area like New York or San Francisco may not support the more violent aspects of tough-on-crime politics, but is mostly okay with more police presence. The average self-identified leftist may be more worried that having police patrols will lead to more brutality than that not having them will lead to more crime, but the average self-identified leftist is not the average voter even in the Bay Area.

In this reality, there are cops on the subway because a lot of people worry about crime on the subway and want to see more police presence. The cops themselves, who are well to the right of the average voter pretty much anywhere, may justify this in terms of fare beating, but what matters is what voters near the median think, and they worry about ordinary property and violent crime. Those worries may well be unfounded – for one, New York is very safe nowadays and has been getting steadily safer, so the recent binge of hiring more cops to patrol the subway is a waste of money – but so long as voters have them, there will be police patrols.

The upshot is twofold. First, fare enforcement and the politics of criminal justice have very little to do with each other. Cops patrol crowded public spaces that require payment to enter, like the subway, as they do crowded public spaces that do not, like city squares. If public transportation fares are abolished, cops will likely keep patrolling subway stations, just as they patrol pieces of transportation infrastructure that are fare-free, like the concourses of major train stations.

If the left succeeds in persuading more people that the police is hostile to their interests and the city is better off with less public police presence, then cops will not patrol either the subway or most city squares. In the future, this is not outside the realm of possibility – in fifteen years the popularity of same-sex marriage in the US went from about 2-to-1 against to 2-to-1 in favor, and the trend in other democracies is broadly similar. But in New York and San Francisco in 2020, this is not the situation.

And second, fare enforcement can be conducted with unarmed inspectors regardless of the political environment. Multiple Americans who express fear of crime have told me that inspections have to be done with armed police, because fare beaters are so dangerous they would never submit to an unarmed inspector. And yet, even in San Francisco, where a large fraction of the middle class is worried about being robbed, inspections are done without weapons.

I’ve recurrently told American cities to tear down the faregates. BART’s belts-and-suspenders fare enforcement is unnecessary, borne of a panic rather than of any calculation of costs and benefits to the system. But what BART should get rid of is not the ambassadors, but the faregates. The most successful transit city the rough size of San Francisco – Berlin – has no faregates and leaves most stations unstaffed to reduce costs. Berlin encourages compliance by making it easier to follow the law, for example by offering cheap monthly passes, rather than by hitting passengers in the face with head-level fare barriers.

If cops patrol the subway because most voters and most riders would prefer it this way, then there is no need to connect the politics of policing with the technical question of what the most efficient way to collect fares is. There is a clear best practice for the latter, and it does not involve faregates in a rapid transit system with fewer than multiple billions of annual riders. What the police does is a separate question, one that there is no reason to connect with how to raise money for good public transportation.

The Different Travel Markets for Regional Rail

At a meeting with other TransitMatters people, I had to explain various distinctions in what is called in American parlance regional rail or commuter rail. A few months ago I wrote about the distinction between S-Bahn and RegionalBahn, but made it clear that this distinction was about two different things: S-Bahns are shorter-distance and more urban than RegionalBahns, but they’re also more about service in a contiguous built-up area whereas RegionalBahns have the characteristics of interregional service. In this post I’d like to explore the different travel markets for regional rail not as a single spectrum between urban and long-range service, but rather as two distinct factors, one about urbanity or distance and one about whether the line connects independent centers (“interregional”) or a monocentric urban blob (“intraregional”).

This distinction represents a two-dimensional spectrum, but for simplicity, let’s start with a 2*2 table, so ubiquitous from the world of consulting:

Connection \ Range Short Long
Intraregional Urban rail, S-Bahn Big-city suburban rail
Interregional Polycentric regional rail RegionalBahn

The notions of mono- and polycentricity are relative. Downtown Providence, Newark, and San Jose all have around 60,000 jobs in 5 km^2. But Caltrain and the Providence Line are both firmly in the RegionalBahn category, the other end being Downtown San Francisco or Boston, 70-80 km away with 300,000-400,000 jobs in 5-6 km^2. Newark, in an essentially contiguous urban area with New York, 16 km from Midtown and its 1.2 million jobs in 6 km^2, is relatively weaker and does not fit into the interregional category; a New York-Newark line is an S-Bahn.

Size matters

On the 2*2 table, the appellations “big-city” and “polycentric” are necessary. This is because longer-range rail lines are likelier to get out of the city and its immediate suburbs and connect to independent urban centers. Exceptions mostly concern the size of the primary urban cluster. If it is large, like New York, it can cast a shadow for tens of kilometers in each direction: commuter volumes are high from deep into Long Island, as far up the Northeast Corridor as Westport, as far up the Hudson as northern Westchester, and so on. In Paris, I wouldn’t be comfortable describing any of the RER and Transilien lines as RegionalBahn. In London, the closest independent cities of reasonable size are Cambridge, Brighton, Oxford, and Portsmouth, the first two about 80 km away and the last two about 100.

Tokyo, about as big as New York and London combined, casts an even longer shadow. In my post on S-Bahns and RegionalBahns I called some of its outer regional rail branches RegionalBahn, giving the examples like the Chuo Line past Tachikawa. But even that line is not really interregional in any meaningful way. It stays within the Tokyo prefecture as far as Takao, 53 km from Tokyo Station, and commuter service continues until Otsuki at kp 88, but everything along the line is bedroom communities for Tokyo or outright rural. The branching and short-turns at Tachikawa mean that the Chuo Line through Tachikawa is a long S-Bahn, and past Tachikawa is really a suburban commuter line too long to be an S-Bahn but too monocentric and peaky to be Regionalbahn (the peak-to-base frequency ratio is about 2:1, whereas German RegionalBahn is more commonly 1:1).

At the other end, we can have regional rail that is short-range but connects two distinct centers. This occurs when relatively small cities are in proximity to each other. In a modern first-world economy, these cities would form a polycentric region, like the Rhine-Ruhr or Randstad. Smaller regions with these characteristics include the Research Triangle, where relatively equal-size Raleigh and Durham are 40 rail kilometers apart, and Nord, where Lille is 30-50 km from cities like Douai and Valenciennes. This may even occur in a region with a strong primary center, if the secondary center is strong enough, as is the case for Winterthur, 28 km from Zurich, which has Switzerland’s fourth highest rail ridership.

Size is measured in kilometers, not people. Stockholm is a medium-size city region, but Stockholm-Uppsala is firmly within RegionalBahn territory, as the two cities are 66 km apart. Randstad’s major cities are all closer to each other – Amsterdam-Rotterdam is about 60 km – and that’s a region of 8 million, not 3 million like Stockholm and the remainder of Uppland and Södermanland.

The issue of frequency

The importance of the 2*2 table is that distance and urban contiguity have opposite effects on frequency: high frequency is more important on short lines than on long lines, and matching off-peak frequency to peak frequency is more important on interregional than intraregional lines.

Jarrett Walker likes to say that frequency is freedom, but what frequency counts as freedom depends on how long passengers are expected to travel on the line. Frequency matters insofar as it affects door-to-door travel time including wait time, so it really ought to be measured as a fraction of in-vehicle travel time rather than as an absolute number. An urban bus with an average passenger trip time of 15 minutes should run every 5 minutes or not much longer; if it runs every half hour, it might as well not exist, unless it exists for timed connections to longer-range destinations. But an intercity rail line where major cities are 2 hours apart can easily run every half hour or even every hour.

The effect of regional contiguity is more subtle. The issue here is that an intraregional line is likely to be used mostly by commuters at the less dense end. The effect of distance can obscure this, but within a large urban area, a 45-minute train will be full of commuters traveling to the primary city in the morning and back to the suburbs in the afternoon or evening; the same train between two distinct cities, like Boston and Providence, will not have so many commuters. In contrast, the same 45-minute trip will get much more reverse-commute travel and slightly more non-commute travel if it connects two distinct cities, because the secondary city is likelier to have destinations that attract travelers.

In no case are the extreme peak-to-base ratios of American commuter lines justifiable. Lines with tidal commuter flows can run 2:1 peak-to-base ratios, as is common in Tokyo, but much larger ratios waste capacity. The marginal cost of service between the morning and afternoon peaks is so low until it matches peak service that having less midday than peak service at all is only justifiable in very peaky environments. The 45-minute suburbs of New York, Tokyo, and other huge cities can all live with a 2:1 ratio, but other lines should have lower ratios, and interregional lines should have a 1:1 ratio.

The implication is that just as peak-to-base ratios going as high as 2:1 are acceptable for long-range intraregional lines, short-range interregional lines must run a constant, high frequency all day. I would groan at the thought of even half-hourly frequency on a 40-km interregional line; the worst I’m comfortable with is 15-20 minutes all day. Of note, such lines are necessarily pretty fast, since by assumption they make few intermediate stops to speed up travel between the two main cities – if there are significant cities in the middle then the lines connect even shorter-range cities and should be even more frequent.

Urban, suburban, intercity

Individual lines may have the characteristics of multiple variants of regional rail. They pass through urban neighborhoods on their way to outlying areas, which may be suburbs or independent cities; they may also pass through multiple kinds of independent areas.

In practice, in big cities this leads to three tiers on the same line: urban at the inner end, suburban at the middle end, interregional at the outer end. Inversions, in which there are independent cities and then suburbs, are possible but extremely rare – I can’t think of any in Paris, London, or New York, and arguably only three in Tokyo (Chiba, Saitama, Yokohama); fundamentally, if there are suburbs of the primary city beyond your municipality, then your municipality is likely to itself be popular as a suburb of the primary city.

That regional lines have these three tiers of demand type does not mean that every single regional line does. Some lines don’t reach any significant independent city. Some don’t usefully serve close-in urban areas – for example, the Providence Line barely serves anything urban, since the stop spacing is wide in order to speed up travel to high-demand suburbs and to Providence and the closest-in urban neighborhoods have Orange Line subway service. In rare cases, the suburban tier may be skipped, because there just isn’t much tidal suburban commuter ridership; in Boston, the Newburyport Line is an example, since its inner area has unbroken working-class urban development almost all the way to Salem, and then there’s almost nothing between Salem and Newburyport.

This does not mean that suburbs are always in between urban areas and independent cities – this is just a specific feature of large metropolitan areas. In smaller ones, the middle tier between urban and long-range interregional service is occupied by short-range interregional service rather than suburban commuter rail. Skipping the suburban tier, which is rare enough in large cities that in the cities I think about most often the only example I can come up with is the Newburyport Line, is thus completely normal in smaller cities.

Conclusion

There are common best practices for commuter rail: electrification, level boarding, frequent clockface schedules, timed transfers, fare integration, proof of payment fare collection.

However, high frequency means different things on lines of different characteristics. An interregional line should be running consistent all-day frequency, and if it is long enough could make do with half-hourly trains with timed connections to suburban buses; an urban line should be running every few minutes as if it were a metro line. Regional rail lines with characteristics off the main diagonal of the S-Bahn to RegionalBahn spectrum have different needs – suburban lines can have high peak frequency to reduce road congestion, although they should still have useful off-peak frequency; short-range interregional lines should run every 10-20 minutes all day.

The distinctions between intraregional and interregional lines and between short- and long-range lines may also affect other aspects of planning: station spacing, connections to local surface transit, connections at the city center end, through-running, etc. Even when the best industry practices are the same in all cases, the relative importance of different aspects may change, which changes what is worth spending the most money on.

Since an individual line can serve multiple markets on its way from city center to a faraway outlying terminal, it may be useful to set up a timetable that works for all of these markets and their differing needs. For example, urban lines need higher frequency than suburban and interregional ones, so a regional line with significant urban service should either branch or run short-turn trains to beef up short-range frequency. If there is a suburban area in the middle with demand for high peak frequency but also a secondary city at the outer end, it may be useful to give the entire line high all-day frequency, overserving the line off-peak just because the cost of service is low.

Ultimately, regional rail is about using mainline rail to fulfill multiple functions; understanding how these functions works is critical for good public transportation.

Why Do Public Transportation Commuters Outearn Car Commuters in Some American Cities?

More than a year ago, I compared Los Angeles with a number of other large American cities. I brought up issues of public transportation ridership, city center job concentration, and income differences, as in the Los Angeles region people who commute by public transit average barely half the earnings of people who drive alone. One of the things noted in that post is that in the secondary transit cities of the United States – Chicago, San Francisco, Washington, Boston – people who commute by transit outearn people who do not. I didn’t delve deeply into that issue in that post, but in this post I will, because it showcases a serious problem in all four cities. New York lacks this pattern as of 2017 – solo drivers outearn transit commuters, though by a small and declining margin, so by 2020 it may join the secondary cities.

The reason this is a problem is that in none of these cities is public transportation so good as to be a luxury good. Rather, the issue is that public transportation is mostly an option for people traveling to city center, where incomes are higher. Crosstown public transportation options are weak – there is rarely direct rapid transit, and transfer trips are inconvenient. There may also be a peak vs. off-peak artifact, but I have no data confirming that richer Americans are likely to commute at rush hour, when transit frequencies are higher and congestion is worse.

Income by mode of transportation to work

From the 2017 American Community Survey, we can grab data about median earnings for workers by their main mode of travel to work:

Metro area Workers PT mode share PT income Solo driver income Median income
New York 9,821,147 31% $44,978 $48,812 $45,150
Chicago 4,653,591 12.2% $46,796 $41,817 $41,232
Philadelphia 3,320,895 9% $37,213 $46,638 $43,472
Washington 2,915,178 12.8% $60,420 $53,390 $52,350
Boston 2,572,454 13.4% $50,593 $51,295 $50,201
San Francisco 2,371,803 17.4% $62,500 $54,923 $54,105
Seattle 1,997,545 10.1% $51,635 $50,183 $41,190

Other modes exist too, most notably carpooling, which has lower median incomes than both solo driving and public transport in all of the cities in the table. Also of note, public transportation user income is more polarized – even though the median is comparable to and usually even higher than the overall median, the poverty rate for transit commuters is higher than the general rate everywhere except in San Francisco, where the poverty rates are within the margin of error.

Why?

Car ownership increases with income. In Singapore, the highest-transit use city for which I have this data, the overall mode share is 58.7%, which splits as low 60s for roughly the bottom half of the income distribution and then less in higher categories, bottoming at 43% in the highest income category, covering the top 15%. It’s really weird that in American cities with public transportation we see the opposite pattern – transit usage is higher in higher income brackets.

The explanation has to be about where people work. OnTheMap doesn’t have great income data, but we can still compare the proportion of workers in the highest income category, which is $3,333/month. I’ve used different definitions of city center in different blog posts: the one about Los Angeles used a restricted one, just a few blocks by a few blocks, covering a single-digit percent of the region, whereas more recently I’ve made 100 km^2 blobs, covering one third of workers in some cities, to maintain comparability with Paris. For this post’s purposes, I’m going to use a definition around the center of a radial transit network (as in the LA post), as well as a looser definition corresponding to something like city limits; in Washington and New York the restricted definitions are somewhat looser to take into account the spread of the subway network just outside city center, but in Chicago and San Francisco the LA post’s definition is apt.

Metro area Workers $40,000+ City Workers $40,000+ CBD Workers $40,000+
New York 9,408,498 52.1% City proper 4,367,781 55.4% South of 60th 2,098,740 65.7%
Chicago 4,604,044 47.9% City proper 1,373,969 53.2% LA post 401,169 71.7%
Washington 2,830,896 55% DC, Arl. 714,075 63% Mass., 395, water 270,299 72.2%
Philadelphia 2,853,154 49.5% City proper 684,869 50.9% Center City 240,665 61.9%
Boston 2,682,278 56.3% Boston, Cam. 787,287 66% Arl., Stuart, water 228,300 72.1%
San Francisco 2,400,290 59.2% City proper 723,907 65.5% LA post 231,042 76.8%
Seattle 1,919,635 57.8% City proper 585,480 64.1% Jackson, I-5, Denny 180,482 71.2%

In all cities, the proportion of workers earning $40,000 a year or more is higher in the city than in the rest of the region, and higher yet in the CBD. Moreover, this effect is weakest in Philadelphia, which may explain why there, unlike in the other secondary transit cities, drivers still significantly outearn transit commuters.

Crosstown public transportation

In all the cities studied in this post, public transportation carries a high share of trips into city center, especially at rush hour. This props up its usage numbers among the middle class, especially the upper middle class – professional jobs cluster in city center.

The problem is that not everyone works in city center. Midtown and Downtown Manhattan are 22% of metro New York employment going by OnTheMap’s LEHD numbers, and even that is a pretty hefty area. In smaller cities, there are necessarily fewer rapid transit lines and a smaller zone of intersection in which service is good from all directions. Improving transit service to destinations outside city center, and thus for working- and lower middle-class jobs, requires more than just disjointed center-to-bedroom-communities rail lines.

One way to have vigorous crosstown public transportation is with buses. However, buses are slow, almost by definition slower than cars. Chicago has a pretty good bus grid, but it still has the pattern of transit commuters outearning solo drivers. And that’s in the city proper – in the suburbs it’s not really possible to have a bus grid, because distances are too great and street networks are usually too broken.

Instead, a better solution has to involve diagonal trips on rapid transit, with a transfer in or near city center, and trips that stay outside city center. A good recipe includes all of the following:

  • Easy downtown and near-downtown transfers, with no missed connections and a minimum of walking. San Francisco deserves especial demerits for forcing people to transfer between Muni and BART via the street, crossing two sets of faregates.
  • High frequency on commuter rail in both directions, with timed bus shuttle connections from stations to office parks too far to walk. In some cases, such buses can do double duty ferrying suburban commuters to those stations for trains to city center.
  • Complete fare integration, with free transfers and mode-neutral fares, to avoid forcing low-income commuters onto slow buses while richer ones get faster trains.
  • Through-running when feasible, since a worker in one neighborhood may end up finding a job at a suburban job site on another line, even the opposite side of the city, e.g. between Brooklyn or Queens and Newark.

Income differences and universal design

The principles for good crosstown service are largely class-neutral. They have to be: the differences between where rich and poor people work in a deindustrialized country are real but not enormous, enough to be noticeable but not enough to play to populist clichés of two Americas. Nonetheless, better public transportation service to non-CBD destinations is especially useful for the working class, because the working class is less likely to work in the CBD than the middle class.

The relevance of class here is twofold. First, every demographic pattern in transportation mode choice has a reason, and provides hints as to how different people travel. This is the case regardless of whether the socially more dominant group commutes by public transport more (the rich, the educated) or less (the native-born, men, whites in Western countries). It remains the case even when there’s no obvious social dominance hierarchy between the groups we compare, for examples professionals versus small business owners.

And second, the people who manage public transportation agencies are drawn from one social class. They are middle-class managers working in city center at traditional peak hours. They may not be aware of how other people commute, regardless of whether those other people are retail workers working two part-time jobs in two different neighborhoods or tech workers who work 12-8. They provide the service that people who are like them can use, and neglect other use cases.

Queens Bus Redesign

New York City Transit has just released its draft redesign for the Queens bus network. It’s a further-reaching reform than what was planned for the Bronx. I’m still seriously skeptical about a number of aspects, but this redesign is genuinely a step forward. The required changes are for the most part tweaks, with just one big change in concept.

What’s in the redesign?

The redesign goes over the local and express bus routes in Queens. I am not going to look at the changes to the express buses, which are not an important part of the network anyway; Queens has a total of 674,000 local bus passengers per weekday and only 15,000 express passengers.

The changes to the local buses include a from-scratch redesign of the network; four new color-coded brands for the local buses; stop consolidation depending on color coding, of which the tightest spacing proposed is 400 meters; and a list of priority corridors where buses are to get dedicated lanes. The scope is only the Queens buses, but there are some new Brooklyn connections: the Metropolitan and Flushing Avenue routes (the new QT3, QT4) keep running through, as they do today, but the Myrtle Avenue route, the current Q55 and new QT55, stops at Ridgewood with a forced transfer to the Brooklyn Myrtle Avenue route.

The four color-coded brands are an unusual, though not unheard of, system. There are four distinct brands among the redesigned Queens buses: blue, red, purple, green. Blue is essentially select bus service, retaining the long stop spacing (“over a mile”), potentially intersecting some bus routes without a transfer; the point is to connect high-demand areas like Flushing with Jamaica. The other three are for various regular local routes. Red routes are distinguished exclusively in having slightly wider stop spacing, 660 meters versus 450 for purple and 400 for green, but otherwise look similar on the network map. Purple and green routes are distinguished in that purple routes are branded for neighborhoods far from the subway and intended to get people from outlying points to subway stations.

What’s good about it?

Stop consolidation is important and I’m glad to see it get play in New York. The choice of interstation across the non-blue routes is solid and close enough to the theoretical optimum that the exact value should depend on ensuring every intersection has an interchange rather than on squeezing a few extra seconds of door-to-door trip time for non-transfer passengers.

The same goes for the decision to designate 21 corridors as top priorities for dedicated bus lanes. The plan does not promise bus lanes on all of them, since the ultimate decision is in the hands of NYCDOT and not the state-owned MTA/NYCT. But it does the best it can, by putting the proposal front and center and announcing that these corridors should be studied as candidates for bus priority. Most of the important streets in Queens are on the list; the only glaring omissions are Union Turnpike, Myrtle, and Metropolitan.

The above two points are not strictly about the redesign. This is fine. When Eric Goldwyn and I tried estimating the benefits of our Brooklyn bus redesign plan, we found that, taking speed, access time, and frequency into account, the redesign itself only contributed 30% of the overall improvement. Stop consolidation and bus lanes contributed 30% each, and off-board fare collection 10%. The Queens plan at the very least has stop consolidation, off-board fare collection as planned when the OMNY smartcard is fully rolled out, and partial use of bus lanes.

But the bus network as redesigned has notable positive features as well. There’s greater reliance on the full network, for one. The JFK AirTrain is free for passengers boarding at Lefferts Avenue or Federal Circle rather than at the subway connection points at Jamaica and Howard Beach, and so the Lefferts Avenue route to JFK, the current Q10 and future QT14, stops at the AirTrain station instead of going all the way to the terminals.

Elsewhere, the bus network is more regular, with fewer bends. The network does not assume away the borough’s important nodes: you can still figure out where Flushing and Jamaica are purely from looking at the map. But it does offer some routes that bypass these nodes for crosstown traffic, for example the redesigned QT65, straightening the current Q65.

What’s bad about it?

The four-color system is just bad. The blue routes are understandable but still bad: they split frequency, so that passengers living next to the local stations on shared routes like Main Street get poor service. The red-purple-green distinction is superfluous – the map really does not make it clear how a red route differs from the others, and the purple and green routes are really the same kind of local bus, just one with a distinguished node at a subway stop and one where there may be multiple distinguished nodes.

The frequencies offered are also weak. Some routes are proposed to run every 8 minutes all day, namely QT route numbers 6, 10, 11, 14, 15, 16, 17, 19, 20, 32, 52, 55, 58, 66, 69, 70. Exactly one is proposed to run more frequently, the QT44 every 5 minutes. The rest run every 10-12 minutes or worse. On weekends, even the 8-minute routes drop to 10-15 minutes. Many routes are quite peaky and there’s no easy distinction between routes for which the report proposes an all-day headway (including all the 8-minute ones above) and ones for which the report proposes separate peak and base headways; the purple routes in general look somewhat peakier than the others, but it’s not a consistent distinction.

If the frequencies are weak, then it means that either the buses are too slow, or there are too many route-km to split a fixed service-hours budget across. NYCT mistakenly thinks that bus costs scale with service-km rather than service-hours, so the planned speedups can in fact be spent on more frequency, but it’s not enough to create a vigorous frequent network. Some pruning is needed; overall the network seems very dense to me, even in areas with decent subway coverage.

A few individual routes are weak too – I don’t think the QT1 idea, paralleling the Astoria Line on 21st Street and then the G train to Downtown Brooklyn, is a good idea. There are two more north-south routes running through to Williamsburg, where the relevant buses are pretty weak and pruning is advisable in order to redeploy service-hours to areas with more demand. If there’s somehow money that can only be spent on north-south service through Williamsburg, it’s better to increase frequency on the G train, which is faster than any bus could ever be.

Is this redesign valuable, then?

Yes! Between the stop consolidation, partial installation of bus lanes, and some of the aspects of the new network, the proposal looks like a two-thirds measure, at worst. It can’t be a full measure because there are serious drawbacks to the plan, not just on the level of details (i.e. too much service to Williamsburg) but also on the conceptual level of the four distinct brands. But it is a noticeable improvement over the current system, and I expect that if it is implemented, even with its many current flaws, then Queens will see a serious increase in bus patronage.

Moreover, the flaws in the plan are not inherent to it. If someone showed me the bus map without the color coding, just with stops and frequencies, I would not even notice the red-green-purple distinction. The blue routes I would notice, and suggest be reduced to the usual stop spacing of everything else; but the others, I wouldn’t. So even the most fundamentally bad part of the plan can be jettisoned while retaining all the good. Everything else is a tweak, and I expect that tweaks will happen one way or another.

Right now comes the community meetings stage, in which existing riders who have too much time will yell, and potential riders who don’t currently take the bus because it’s too slow don’t show up at all. The plan will be tweaked, and the tweaks may well make it worse rather than better. But what good transit activists in New York say matters, and so far the reaction should be positive, demanding certain changes but keeping the gist of the redesign.

Outlying S-Bahn Tunnels

There’s a thread on Twitter by Stephen Smith bringing up Zurich’s S-Bahn as an alternative to extensive metro tunneling. It reminded me of something I’d been meaning to write about for a long time, about how S-Bahn tunnels, in Zurich and elsewhere, include not just the bare minimum for through-running but also strategic tunneling elsewhere to reach various destinations not on the mainline. Zurich’s S-Bahn includes about 19 km of tunnel built since the 1960s, which is similar per capita to the amount of tunneling built for the Washington Metro.

Such tunneling is important to ensure a regional rail network reaches destinations off the mainlines. Even cities with metro systems need to understand this as long as they have some mainline rail serving suburban destinations. For example, in the Center of Israel, Tel Aviv is getting a subway-surface light rail network, but outside the urban core rail transport will remain dominated by Israel Railways service; as Israel Railways avoids many city centers, such as Netanya, short strategic tunnels are critical.

Tunnels in Zurich

The core of the Zurich S-Bahn is three city center tunnels: the 2 km Käferberg Tunnel from Oerlikon to Hardbrücke, the 7 km combination of the Hirschengraben Tunnel and the Zürichberg Tunnel from Hauptbahnhof to the Right Bank of Lake Zurich and points northeast, and the 5 km Weinberg Tunnel from Hauptbahnhof to Oerlikon and points north. The Käferberg Tunnel is from the 1960s, the Hirschengraben and Zürichberg Tunnel opened in 1989-1990 as the core of the Zurich S-Bahn, and the Weinberg Tunnel opened in 2014 as a second S-Bahn route to add more capacity.

These 14 km of tunnel look like any standard picture of regional rail tunneling. However, Zurich has in addition built a 5 km tunnel for a loop to the airport. Without this tunnel, no regional or intercity rail service to the airport would have been possible, as the airport was at a distance from the mainline; only trams could have served the airport then.

In addition to these 19 km, there is some talk of building an additional tunnel of 7-10 km on the Zurich-Winterthur Line, called the Brüttener Tunnel, to speed up service between these two cities.

Tunnels on other regional rail systems

In Paris, the RER consists not just of legacy rail track and city center tunnels, but also outlying tunnels reaching new destinations. The RER B connection to Charles de Gaulle Airport is new construction, opening in 1976 as a commuter line just before the RER opened and incorporated it as a branch. It’s a mix of above- and underground construction, totaling 5.5 km of tunnel. Two more key RER lines, at both ends of the RER A, are new: the branch to Cergy, which opened between 1979 and 1994 and has 3 km of tunnel, and the branch to Marne-la-Vallée, which opened in stages starting on the same day as the RER A’s central tunnel and continuing until reaching its terminus in 1992.

All three new RER branches are busy. They have to be – if there weren’t so much demand for them, it would have been financially infeasible to build them and those areas would have had to make do with a bus connection to the existing mainlines. The Marne-la-Vallée branch carries about two thirds of the eastern branch ridership of the RER A, making it most likely the busiest single rail branch in Europe.

In London, the regional rail network is less modern than in Paris, Zurich, and other cities with extensive development of new tunnels. Nonetheless, the Crossrail plans do include a short outlying tunnel reaching Heathrow Airport. Moreover, one of the two eastern branches of the mainline has the characteristics of an outlying tunnel, namely the branch to Canary Wharf. Canary Wharf is only 5 km from the City of London and the tunnel connecting to it is contiguous with the central tunnel, but the branch is not really about improving connections to onward suburbs. Where La Défense was always on the way to western suburbs on the RER, Canary Wharf is only on the way to Abbey Wood. There are proposals among area railfans to extend this branch much farther to the east, but no official plans that I know of. In the currently planned paradigm for Crossrail, Canary Wharf is purely a destination.

In Munich, there is a new line toward the airport, with some tunneling on airport grounds as well as at two intermediate suburban stations. There is also a short above-ground spur connecting the airport to the western side of the S-Bahn, giving it two different routes to city center. Finally, there is a short tunnel slightly to the west of the main trunk tunnel to better connect S7 to the mainline.

Why are airports so prominent on this list?

The concept of using strategic tunnels to build new spurs and loops to connect mainlines to new destinations has nothing to do with airports. And yet, so many of these spurs connect to airports: Charles de Gaulle, Heathrow, Zurich, Munich. There are many more such examples, on regional or intercity lines: Schiphol, Arlanda, Ben-Gurion, soon-to-be Berlin-Brandenburg, Barajas. Why is that?

The answer is that the purpose of a spur or loop is to connect to a destination off the mainline. European cities for the most part developed around the railway or metro line. Virtually every important destination in London is on a legacy railway because during the city’s 19th and early 20th century growth period, the railway was the only way to get to Central London. Airports are consistent exceptions because they’re so land-intensive that it’s hard to site them near existing railways.

Where non-airport destinations somehow had to be developed away from the mainline, they’re attractive targets for spurs as well. Canary Wharf sits on the site of a disused dock, which generated some freight rail traffic but little demand for passenger rail. Cergy is one of several new towns built around Paris to act as suburban growth nodes, together with Marne-la-Vallée and Évry (served on a loop of the RER D).

In smaller cities than Paris and London, suburban growth often came together with a metro line. In Stockholm, the Metro was planned together with public housing projects, so many of the Million Program projects are right next to stations, facilitating high public transportation usage. There’s usually no need to build many new regional rail spurs, because such sites are close enough to the center for metro service to be quick enough.

The situation of regional rail in Israel

In Israel, urban development has ignored the railway almost entirely. The colonial network was weak and barely served the state’s travel needs. Investment was minimal, as the state’s political goals were population dispersal and Judaization of peripheral areas rather than efficient transportation. Towns were built around the road network, connected to one another by bus since people were too poor to afford cars.

Rail revival began in the early 1990s with the opening of the Ayalon Railway, providing through-service between points north and south of Tel Aviv. In the generation since, ridership has grown prodigiously, albeit from low initial levels, and the state has built new lines, with an ongoing project to electrify most of the passenger network. However, since the cities came first and the trains second, the new lines do not enter city centers, but rather serve them peripherally near the highway, often surrounded by parking.

Thus, Netanya’s train station is located to the east of the city’s built-up area, on the wrong side of the Route 2 freeway. Ashdod’s train station is on the periphery at a highway interchange, well to the east of city center. Ashkelon’s station is on the eastern margin. The under-construction line through Kfar Saba and Ra’anana passes just south of the built-up area.

In all of these cases, doing it right would require, or would have required, just short, strategic elevated or underground lines:

  • Netanya is at the northern end of the Tel Aviv commuter rail network, and so it can easily be served by a spur. The existing station can be retained as a junction for intercity rail service, but building a commuter rail spur would not compromise frequency. Such a spur would require no more than 2 km of tunnel.
  • In Ashdod and Ashkelon, there are north-south arterials that are so wide, 50-60 meters, that they could host cut-and-cover subways, effectively moving the line to the west to serve those cities better. In Ashdod there is a decision between going under B’nai Brith, which offers a more convenient through-route, and Herzl, which is more central but requires some boring at the southern end of the city.
  • In Kfar Saba and Ra’anana, about 8 km of tunnel under Weizmann and Ahuza are needed, and could potentially be done cut-and-cover as well, but these streets are 30 meters rather than 50 meters wide. Such a route would replace the under-construction combination of a freeway and railway.
  • In Rishon LeZion, a 6km route, not all underground, is needed to connect Rishonim with Moshe Dayan via city center and the College of Management rather than via the under construction freeway route avoiding these destinations.

Unfortunately, so far the state’s investment plans keep skirting city centers. It serves them with a cars-and-trains paradigm, which assumes the rail passenger is driving or riding a bus to the train station, never mind that in that case it’s more convenient to drive all the way to one’s destination. This suppresses ridership; not for nothing, the busiest station outside metropolitan centers is Rehovot, with 2.1 million annual entries, and not Ashdod, which is second with 1.9 million. Ashdod is a city of 220,000 and Rehovot one of 140,000, but Rehovot’s station is far more walkable. Were Ashdod not poor, few people would use the station at all – they’d all just drive.

Off-Peak Public Transport Usage

Earlier this year, I slowly stumbled across something that I don’t think is well-known in comparative public transportation: European cities have much higher public transport ridership than someone experienced with American patterns would guess from their modal splits. From another direction, Europe has much lower mode share than one would guess from ridership. The key here is that the mode share I’m comparing is for work trips, and overall ridership includes all trip purposes. This strongly suggests that non-work public transportation usage is much higher in European than in American cities even when the usage level for work trips is comparable. Moreover, the reason ought to be better off-peak service in Europe, rather than other factors like land use or culture, since the comparison holds for New York and not only for truly auto-oriented American cities.

Modal shares and ridership levels

My previous post brings up statistics for work trip mode share in England and France. For the purposes of this post, I am going to ignore England and focus on France and wherever I can find data out of Germany and Austria; the reason is that in the secondary cities of England, public transport is dominated by buses, which are hard to find any ridership data for, let alone data that doesn’t have severe double-counting artifacts for transfer passengers. For the same reason, I am not going to look at Canada – too many transfer artifacts.

In contrast, French and German-speaking metro areas with rail-dominated public transport make it relatively convenient to count rail trips per capita, as do the more rail-oriented American metro areas, namely Boston, New York, and Washington. A secondary check involving both bus and rail can be obtained from The Transport Politic, comparing the US with France.

City Population Definition Trips/year Trips/person Mode share
Boston 4,900,000 Subway, commuter rail 204,000,000 42 12%
New York 20,000,000 Subway, PATH, LIRR, MN, NJT Rail 2,050,000,000 103 31%
Washington 6,200,000 Metro, MARC (daily*280), VRE (daily*250) 245,000,000 40 12%
Vienna 3,700,000 U-Bahn, trams, S-Bahn (PDF-p. 44) 822,000,000 222 40%
Berlin 5,000,000 U-Bahn, trams, S-Bahn 1,238,000,000 248 35%
Hamburg 3,100,000 U-Bahn, S-Bahn 531,000,000 171 26%
Stuttgart 2,400,000 Stadtbahn, S-Bahn, Regionalbahn 223,000,000 93 26%
Lyon 2,300,000 Métro, trams, funiculars, 0.5*TER 325,000,000 141 20%
Marseille 1,800,000 Métro, trams (daily*280), 0.5*TER 139,000,000 77 16%
Toulouse 1,300,000 Métro, trams 125,700,000 97 13%
Bordeaux 1,200,000 Light rail 105,500,000 88 13%
Lille 1,200,000 Métro, trams 108,500,000 90 17%

 

Note that New York, with a 31% mode share, has not much more rail ridership per capita than French metro areas with mode shares in the teens, and is a quarter below Lyon, whose mode share is only 20%. This is not an artifact of transfers: just as the subway dominates ridership in New York, so does the metro dominate Lyon, Toulouse, and Lille, and so does the tram dominate Bordeaux. If anything, it’s Stuttgart, the only European city on this list with comparable ridership per unit of mode share to the US, that should have the most overcounting due to transfers.

Also note that French rail ridership nosedives in the summer, when people go on their 5-week vacations, and I presume that this equally happens in Germany and Austria. The ratio of annual to weekday ridership in France where it is available is fairly low, not because weekend ridership is weak, but because the weekday chosen to represent daily ridership is never in the summer vacation season.

Why?

Off-peak public transportation in the United States is quite bad. In New York, 10-minute frequency on most lettered routes is the norm. In Washington, the off-peak frequency is 12 minutes. In Boston, it varies by line; on the Red Line each branch is supposed to come every 12-13 minutes off-peak, but in practice trains don’t run reliably and often leave the terminal bunched, alternating between 3- and 10-minute gaps.

Moreover, commuter trains are so useless except for peak-hour commutes to city center that they might as well not exist. Hourly gaps and even worse are routine, and even the busiest New York commuter lines have at best half-hourly off-peak frequency. These lines are only about 15% of rail ridership in New York and Boston and 6% of rail ridership in Washington, but they contribute a decent volume of commuters who drive for all non-work purposes.

In Berlin, the off-peak frequency on the U-Bahn is a train every 5 minutes most of the day on weekdays. On Sundays it drops to a train every 8 minutes, and in the evening it drops to a train every 10 minutes far too early, leading to overcrowding on the first train after the cut in frequency around 9 pm. The S-Bahn trunks run frequently all day, but the branches in the suburbs only get 10-minute frequency, and the Ring has a 2-hour midday period with 10-minute gaps. The suburban areas with only S-Bahn service get comparable service to neighborhoods on New York subway branches, while closer-in areas get better service. No wonder people use it for more than just work – the train is useful for shopping and socializing at all hours of the day.

Why?

The people who manage public transportation in the United States do not have the same profile as most riders. They work traditional hours, that is 9 to 5 on weekdays only, at an office located in city center. Many senior managers do not use their own system. That NYCT President Andy Byford does not own a car or know how to drive and takes the subway and buses to events is unusual for such a senior person, and early media reports noted that some managers looked askance at his not driving.

Growing segments of the American middle class commute by public transportation. In Boston and Washington, transit commuters slightly outearn solo drivers, and in New York they do not but it is close. But those segments have different travel behavior from public-sector planners. For example, lawyers work long hours and depend on the subway at 8 or 9 pm, and programmers work shifted hours and both show up to and leave work hours after the traditional times. But public transportation agencies still work 9 to 5, and thus the middle-class transit-using behavior they are most familiar with is that of the denizen of the segregated suburb, who drives to all destinations but city center.

In such an environment, off-peak service is treated as a luxury. When there is a deficit, agencies cut there first, leading to frequency-ridership spirals in which lower frequency deters riders, justifying further cuts in service until little is left. In New York, there are guidelines for frequency that explicitly state it is to be adjusted based on ridership at the most crowded point of the route, without regard for whether cuts depress ridership further. There is a minimum acceptable frequency in New York, but it is set at 10 minutes on weekdays and 12 on weekends. For a similar reason, the planners tend to split buses between local and limited routes if each can support 10-12 minute headways, at which point the buses are not useful for short trips.

In contrast, in Germany and France, there is a mixture of drivers and public transportation users among managers. German planning stresses consistent schedules throughout the day, so the midday off-peak often gets the same frequency as the peak. French planning does vary frequency, but maintains a higher base frequency even late into the night. The Paris Métro runs every 5 to 7 minutes at 11 pm. The idea of running a big city metro line every 12 minutes is unthinkable.

On Envying Canada

In England and Wales, 15.9% of workers get to work on public transport, and in France, 14.9% do. In Canada, the figure is close: 12.4%, and this is without a London or Paris to run up the score in. Vancouver is a metro region of 2.5 million people and 1.2 million workers, comparable in size to the metropolitan counties in England and to the metro area of Lyon; at 20.4%, it has a higher public transport modal share than all of them, though it is barely higher than Lyon with its 19.9% share. Calgary, Ottawa, Edmonton, and Winnipeg are likewise collectively respectable by the standards of similar-size French regions, such as the departments of Bouches-du-Rhône (Marseille), Alpes-Maritimes (Nice), Gironde (Bordeaux), Haute-Garonne (Toulouse), and Bas-Rhin (Strasbourg).

As a result, Jarrett Walker likes telling American cities and transit agencies to stop envying Europe and start envying Canada instead. Canada is nearby, speaks the same language, and has similar street layout, all of which contribute to its familiarity to Americans. If Europe has the exotic mystique of the foreign, let alone East Asia, Canada is familiar enough to Americans that the noticeable differences are a cultural uncanny valley.

And yet, I am of two minds on this. The most consistent transit revival in Canada has been in Vancouver, whose modal share went from 14.3% in 1996 to 20.4% in 2016 – and the 2016 census was taken before the Evergreen extension of the Millennium Line opened. TransLink has certainly been doing a lot of good things to get to this point. And yet, there’s a serious risk to Canadian public transport in the future: construction costs have exploded, going from Continental European 15 years ago to American today.

The five legs of good transit

I was asked earlier today what a good political agenda for public transportation would be. I gave four answers, like the four legs of a chair, and later realized that I missed a fifth point.

  1. Fuel taxes and other traffic suppression measures (such as Singapore and Israel’s car taxes). Petrol costs about €1.40/liter in Germany and France; diesel is cheaper but being phased out because of its outsize impact on pollution.
  2. Investment in new urban and intercity lines, such as the Madrid Metro expansion program since the 1990s or Grand Paris Express. This is measured in kilometers and not euros, so lower construction costs generally translate to more investment, hence Madrid’s huge metro network.
  3. Interagency cooperation within metropolitan regions and on intercity rail lines where appropriate. This includes fare integration, schedule integration, and timetable-infrastructure integration.
  4. Urban upzoning, including both residential densification in urban neighborhoods and commercialization in and around city center.
  5. Street space reallocation from cars toward pedestrians, bikes, and buses.

We can rate how Canada (by which I really mean Vancouver) does on this rubric:

  1. The fuel tax in Canada is much lower than in Europe, contributing to high driving rates. In Toronto, gasoline currently costs $1.19/liter, which is about €0.85/l. But Vancouver fuel taxes are higher, raising the price to about $1.53/l, around €1.06/l.
  2. Canadian construction costs are so high that investment in new lines is limited. Vancouver has been procrastinating building the Broadway subway to UBC until costs rose to the point that the budget is only enough to build the line halfway there.
  3. Vancouver and Toronto both have good bus-rapid transit integration, but there is no integration with commuter rail; Montreal even severed a key commuter line to build a private driverless rapid transit line. In Vancouver, bus and SkyTrain fares have decoupled due to political fallout from the botched smartcard implementation.
  4. Vancouver is arguably the YIMBYest Western city, building around 10 housing units per 1,000 people every year in the last few years. Toronto’s housing construction rate is lower but still respectable by European standards, let alone American ones.
  5. There are bike lanes but not on the major streets. If there are bus lanes, I didn’t see any of them when I lived in Vancouver, and I traveled a lot in the city as well as the suburbs.

Vancouver’s transit past and future

Looking at the above legs of what makes for good public transport, there is only one thing about Canada that truly shines: urban redevelopment. Toronto, a metro area of 6 million people, has two subway mainlines, and Montreal, with 4 million people, has 2.5. Vancouver has 1.5 lines – its three SkyTrain mainlines are one-tailed. By the same calculation, Berlin has 6.5 U- and 3 S-Bahn mainlines, and Madrid has 2 Cercanías lines and 7 metro lines. Moreover, high construction costs and political resistance from various GO Transit interests make it difficult for Canadian cities to add more rapid transit.

To the extent Vancouver has a sizable SkyTrain network, it’s that it was able to build elevated and cut-and-cover lines in the past. This is no longer possible for future expansion, except possibly toward Langley. The merchant lawsuits over the Canada Line’s construction impacts have ensured that the Broadway subway will be bored. Furthermore, the region’s politics make it impossible to just build Broadway all the way to the end: Surrey has insisted on some construction within its municipal area, so the region has had to pair half the Broadway subway with a SkyTrain extension to the Langley sprawl.

Put in other words, the growth in Vancouver transit ridership is not so much about building more of a network, but about adding housing and jobs around the network that has been around since the 1980s. The ridership on the Millennium and Canada Lines is growing but remains far below that on the Expo Line. There is potential for further increase in ridership as the neighborhoods along the Canada Line have finally been rezoned, but even that will hit a limit pretty quickly – the Canada Line was built with low capacity, and the Millennium Line doesn’t enter Downtown and will only serve near-Downtown job centers.

Potemkin bus networks

When Jarrett tells American cities to envy Canada, he generally talks about the urban bus networks. Toronto and Vancouver have strong bus grids, with buses coming at worst every 8 minutes during the daytime off-peak. Both cities have grids of major streets, as is normal for so many North American cities, and copying the apparent features of these grids is attractive to American transit managers.

And yet, trying to just set up a bus grid in your average American city yields Potemkin buses. Vancouver and Toronto have bus grids that rely on connections to rapid transit lines. In both cities, transit usage is disproportionately about commutes either to or from a city core defined by a 5 kilometer radius from city hall. Moreover, the growth in public transport commuting in both cities since 1996 has been almost exclusively about such commutes, and not about everywhere-to-everywhere commutes from outside this radius. Within this radius, public transportation is dominated by rail, not buses.

The buses in Toronto and Vancouver have several key roles to play. First, as noted above, they connect to rapid transit nodes or to SeaBus in North Vancouver. Second, they connect to job centers that exist because of rapid transit, for example Metrotown at the eastern end of Vancouver’s 49. And third, there is the sui generis case of UBC. All of these roles create strong ridership, supporting high enough frequency that people make untimed transfers.

But even then, there are problems common to all North American buses. The stop spacing is too tight – 200 meters rather than 400-500, with frequency-splitting rapid buses on a handful of very strong routes like 4th Avenue and Broadway. There is no all-door boarding except on a handful of specially-branded B-line buses. There are no bus lanes.

One American city has similar characteristics to Toronto and Vancouver when it comes to buses: Chicago. Elsewhere, just copying the bus grid of Vancouver will yield nothing, because ultimately nobody is going to connect between two mixed-traffic buses that run every 15 minutes, untimed, if they can afford any better. In Chicago, the situation is different, but what the city most needs is integration between Metra and CTA services, which requires looking at European rather than Canadian models.

Is Canada hopeless?

I don’t know. The meteoric rise in Canadian subway construction costs in the last 15 years has ensured expansion will soon grind to a halt. Much of this rise comes from reforms that the Anglosphere has convinced itself improve outcomes, like design-build and reliance on outside consultants; in that sense, the US hasn’t been copying Canada, but instead Canada has been copying the US and getting American results.

That said, two positive aspects are notable. The first is very high housing and commercial growth in the most desirable cities, if not in their most exclusive neighborhoods. Vancouver probably has another 10-20 years before its developable housing reserves near existing SkyTrain run out and it is forced to figure out how to affordably expand the network. Nowhere in Europe is housing growth as fast as in Metro Vancouver; among the cities for which I have data, only Stockholm comes close, growing at 7-8 net units per 1,000 people annually.

Moreover, with Downtown Vancouver increasingly built out, Vancouver seems to be successfully expanding the CBD outward: Central Broadway already has many jobs and will most likely have further commercial growth as the Millennium Line is extended there. Thus, employers that don’t fit into the Downtown Vancouver peninsula should find a home close enough for SkyTrain, rather than hopping to suburban office parks as in the US. Right now, the central blob of 100 km^2 – a metric I use purely because of limitations on French and Canadian data granularity – has a little more than 30% of area jobs in Vancouver, comparable to Paris, Lyon, New York, Boston, and San Francisco, and ahead of other American cities.

The second aspect is that Canadians are collectively a somewhat more internationally curious nation than Americans. They are more American than European, but the experience of living in a different country from the United States makes it easier for them to absorb foreign knowledge. The reaction to my and Jonathan English’s August article about Canadian costs has been sympathetic, with serious people with some power in Toronto contacting Jonathan to figure out how Canada can improve. The reaction I have received within the United States runs the gamut – some agencies are genuinely helpful and realize that they’ll be better off if we can come up with a recipe for reducing costs, others prefer to obstruct and stonewall.

My perception of Canadian politics is that even right-populists like Doug Ford are more serious about this than most American electeds. In that sense, Ford is much like Boris Johnson, who could move to Massachusetts to be viceroy and far improve governance in both Britain and Massachusetts. My suspicion is that this is linked to Canada’s relatively transit-oriented past and present: broad swaths of the Ontarian middle class ride trains, as is the case in Outer London and the suburbs of Paris. A large bloc of present-day swing voters who use public transport is a good political guarantee of positive attention to public transport in the future. American cities don’t have that – there are no competitive partisan elections anywhere with some semblance of public transportation.

These two points of hope are solid but still run against powerful currents. Toronto really is botching the RER project because of insider obstruction and timidity, and without a strong RER project there is no way to extend public transportation to the suburbs. Vancouver is incapable of concentrating resources where they do the most good. And all Canadian cities have seen an explosion in costs. Canadians increasingly understand the cost problem, but it remains to be seen whether they can fix it.